Thursday, January 24, 2013

Dummy Switch Setup


1)      Reset pwd in Cisco 3550 ( till Step 9 )


 


  1. Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) to the console port of the switch. Use the following terminal settings:
    Bits per second (baud): 9600
    Data bits: 8
    Parity: None
    Stop bits: 1
    Flow Control: Xon/Xoff
  2. Unplug the power cable.
  3. Hold down the mode button located on the left side of the front panel, while reconnecting the power cable to the switch.
    For 2900/3500XL and 3550 Series switches: release the mode button after the LED above Port 1x goes out.
    Note: LED position may vary slightly depending on the model.
    Catalyst 3524XL
    pswdrec_2900xl_1.gif
    For 2950 Series switches: release the mode button after the STAT LED goes out.
    Note: LED position may vary slightly depending on the model.
    Catalyst 2950-24
    pswdrec_2900xl_2.gif
    The following instructions appear:
    The system has been interrupted prior to initializing the
    flash filesystem.  The following commands will initialize
    the flash filesystem, and finish loading the operating
    system software:
        flash_init
        load_helper
        boot
    switch:
    
    !--- This output is from a 3500XL switch. Output from a 2900XL, 2950 or 3550 will vary slightly.
    
    
  4. Issue the flash_init command.
    switch: flash_init
    Initializing Flash...
    flashfs[0]: 143 files, 4 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 3612672
    flashfs[0]: Bytes used: 2729472
    flashfs[0]: Bytes available: 883200
    flashfs[0]: flashfs fsck took 86 seconds
    ....done Initializing Flash.
    Boot Sector Filesystem (bs:) installed, fsid: 3
    Parameter Block Filesystem (pb:) installed, fsid: 4
    switch:
    
    !--- This output is from a 2900XL switch. Output from a 3500XL, 3550 or 2950 will vary slightly.
    
    
  5. Issue the load_helper command.
    switch: load_helper
    switch:
  6. Issue the dir flash: command.
    
    !--- Make sure to type a colon ":" after the dir flash. 
    
    
    The switch file system is displayed:
    switch: dir flash:
    Directory of flash:/
    2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin
    
    !--- This is the current version of software.
    
    4    -rwx  1131                     config.text
    
    !--- This is the configuration file.
    
    5    -rwx  109                      info
    6    -rwx  389                      env_vars
    7    drwx  640                      html
    18   -rwx  109                      info.ver
    403968 bytes available (3208704 bytes used)
    switch:
    
    !--- This output is from a 3500XL switch. Output from a 2900XL, 2950 or 3550 will vary slightly.
    
    
  7. Type rename flash:config.text flash:config.old to rename the configuration file.
    switch: rename flash:config.text flash:config.old
    switch:
    
    !--- The config.text file contains the password definition.
    
    

  8. Issue the boot command to boot the system.
    switch: boot
    Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...###############################
    ################################################################################
    ######################################################################
    File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po
    int: 0x3000
    executing...
    
    !--- Output truncated.
    !--- This output is from a 3500XL switch. Output from a 2900XL, 2950 or 3550 will vary slightly.
    
    
  9. Enter "n" at the prompt to start the Setup program.
    --- System Configuration Dialog ---
    At any point you may enter a question mark '?' for help.
    Use ctrl-c to abort configuration dialog at any prompt.
    Default settings are in square brackets '[]'.
    Continue with configuration dialog? [yes/no]: n 
    
    !--- Type "n" for no.
    
    Press RETURN to get started.
    
    !--- press Return or Enter.
    
    Switch>
    
    !--- The Switch> prompt is displayed.
    

2)      Change pwd
 Enable password Cisco
Ctrl+Z
3)      Write mem
4)      Show vlan
5)      Delete flash:vlan.dat
6)      Reload ( reboot switch )